Search found 17 matches

by smudge611
Thu Dec 12, 2019 1:45 pm
Forum: Alignments
Topic: RPS POSSIBLE SOLUTIONS
Replies: 3
Views: 450

Re: RPS POSSIBLE SOLUTIONS

How exactly do I move the coordinate system?
by smudge611
Wed Dec 04, 2019 7:49 am
Forum: Alignments
Topic: RPS POSSIBLE SOLUTIONS
Replies: 3
Views: 450

RPS POSSIBLE SOLUTIONS

Setting up a program for a Rear Combination Light fixture. During a RPS Alignment I get the Possible Solutions dialogue.
How am I supposed to know which is the correct one to choose?
If you look at the screenshot
Sphere 2 is origin
sphere 3 is rotation and
sphere 1 is align
by smudge611
Wed Nov 13, 2019 11:41 am
Forum: Alignments
Topic: CAD NOT ALIGNED AFTER MIRROR
Replies: 6
Views: 966

Re: CAD NOT ALIGNED AFTER MIRROR

Another issue I have ran into, I did a CAD Alignment Then a Datum Alignment to verify Programmed and ran with good numbers Mirrored and ran program CAD Alignment is fine Datum Alignment throws CAD( and nominal s) way off in space and not Synced Why? See video below https://www.dropbox.com/s/wgteje5g...
by smudge611
Wed Nov 06, 2019 1:51 pm
Forum: Reporting
Topic: Cloud to CAD and No results after verify
Replies: 8
Views: 874

Re: Cloud to CAD and No results after verify

Capture.JPG
Assume you mean this, it is turned off, I will turn it on and see if it changes anything
by smudge611
Wed Nov 06, 2019 11:30 am
Forum: Alignments
Topic: Tooling Ball - CAD - RPS
Replies: 5
Views: 626

Re: Tooling Ball - CAD - RPS

It's all about the location of the cursor during a mirror, I was originally told that the cursor needed to be at the top of the program list during a mirror. this is incorrect. The cursor should be at the bottom so it is actually mirroring the part reference not the machine reference. sync cad had n...
by smudge611
Wed Nov 06, 2019 10:36 am
Forum: Reporting
Topic: Cloud to CAD and No results after verify
Replies: 8
Views: 874

Re: Cloud to CAD and No results after verify

Any response on this yet here is a video showing the issue
https://www.dropbox.com/s/s6prneu2rcji7 ... 2.mp4?dl=0

Thanks
by smudge611
Fri Oct 25, 2019 11:43 am
Forum: Alignments
Topic: CAD NOT ALIGNED AFTER MIRROR
Replies: 6
Views: 966

Re: CAD NOT ALIGNED AFTER MIRROR

Figured it out after trying to mirror again.
Apparently the unmirrored axis should have been x not y
which makes no sense since it was always normally done on the y axis in all my programs in metrolog
by smudge611
Fri Oct 25, 2019 11:00 am
Forum: Alignments
Topic: CAD NOT ALIGNED AFTER MIRROR
Replies: 6
Views: 966

CAD NOT ALIGNED AFTER MIRROR

Okay I imported a CAD did a CAD alignment then a datum alignment to fine tune. set up the program and rand it got good results on the report mirrored the program (fixture is for a LH RH headlamp) made a few naming changes ran the program and below are my results makes no sense. after each alignment ...
by smudge611
Wed Oct 23, 2019 1:16 pm
Forum: Reporting
Topic: Cloud to CAD and No results after verify
Replies: 8
Views: 874

Re: Cloud to CAD and No results after verify

i do that and there results still show up with no deviation unless i actually run the program
by smudge611
Mon Oct 21, 2019 8:17 am
Forum: Alignments
Topic: Tooling Ball - CAD - RPS
Replies: 5
Views: 626

Re: Tooling Ball - CAD - RPS

I figured it out myself, with NO help, and NO response from the helpdesk