Search found 7 matches

by reneramirez17
Mon Apr 13, 2020 2:00 pm
Forum: Wenzel / Pantec
Topic: UCC Server and CMM Manager
Replies: 17
Views: 1706

Re: UCC Server and CMM Manager

After trying a few of the recommendations on here, nothing seems to get my machine working correctly. So, the only thing left to do now I was told by the Calibration folks, was to Laser Calibrate the machine, re mapping within UCC server, once the mapping is stored within the UCC controller, CMM man...
by reneramirez17
Fri Apr 10, 2020 11:26 am
Forum: Wenzel / Pantec
Topic: UCC Server and CMM Manager
Replies: 17
Views: 1706

Re: UCC Server and CMM Manager

It could be that the post-head-calibration procedure wasn't done correctly. The right way to do things... 1. Open and run the head calibration routine in UCC Assist and then close UCC Assist. 2. Open UCC Server and "Clear Calibration" for all tools (including RefTool). 3. Calibrate RefTool 4. Calib...
by reneramirez17
Fri Apr 10, 2020 11:26 am
Forum: Wenzel / Pantec
Topic: UCC Server and CMM Manager
Replies: 17
Views: 1706

Re: UCC Server and CMM Manager

It could be that the post-head-calibration procedure wasn't done correctly. The right way to do things... 1. Open and run the head calibration routine in UCC Assist and then close UCC Assist. 2. Open UCC Server and "Clear Calibration" for all tools (including RefTool). 3. Calibrate RefTool 4. Calib...
by reneramirez17
Thu Apr 09, 2020 10:35 am
Forum: Wenzel / Pantec
Topic: UCC Server and CMM Manager
Replies: 17
Views: 1706

Re: UCC Server and CMM Manager

Ryan Christopher wrote:
Thu Apr 09, 2020 9:48 am
Make sure that your calibration sphere diameter is input correctly in UCC Server too!
Hello Ryan,
Yes, we did. He measured the sphere diameter, made sure everything was correct on that part as well.
by reneramirez17
Thu Apr 09, 2020 9:58 am
Forum: Wenzel / Pantec
Topic: UCC Server and CMM Manager
Replies: 17
Views: 1706

Re: UCC Server and CMM Manager

Yes, the head was calibrated. That was the gentleman's first thing he thought could have been causing the issue, so he did a calibration on the head, but no luck. UCC Server 5.4 and CMM Manager 3.9 SP2. It was working fine previously. What we know is... Everyting was workign fine at the end of the 2...
by reneramirez17
Wed Apr 08, 2020 4:44 pm
Forum: Wenzel / Pantec
Topic: UCC Server and CMM Manager
Replies: 17
Views: 1706

Re: UCC Server and CMM Manager

I am so sorry. I meant to say we are out of tolerance by .001. If it's an ID, it measures oversize, if it's an OD it measures undersize. Everything is off by .001. Size does not matter. It's just off by .001 I do not have a calibrated length bar. We only have ID master gage. We just got the machine ...
by reneramirez17
Wed Apr 08, 2020 9:27 am
Forum: Wenzel / Pantec
Topic: UCC Server and CMM Manager
Replies: 17
Views: 1706

UCC Server and CMM Manager

Hello Everyone, I am hoping someone can help. I recently got my machine calibrated. The gentleman created new "airmaps" on all my axes, did full calibration on the PH20 head and everything. Everything look good in numbers, but when I check ID and OD we are getting the dimensions over size by .001inc...